Hey everyone, thanks for tuning in. If you’re working with loadbreak switches (LBS), you know how critical these little workhorses are—especially if you’re maintaining or troubleshooting your own equipment, or you’ve got a team that’s on call when something goes wrong. As a loadbreak switch supplier, I’ve seen my fair share of both preventable messes and tricky issues that even seasoned techs second-guess. Today, I’m breaking down how to troubleshoot an LBS step by step, no jargon overload, just real-world stuff I’ve picked up from working with field crews for years. First off, let’s cut the fluff: a loadbreak switch isn’t your regular knife switch. It’s built to turn a load on or off even when there’s current flowing—no arcing that fries your gear, right? But that built-in load-breaking capability means it has specific parts that can act up, so we’re gonna focus on the most common snags and how to fix ’em. Loadbreak Switch

Let’s start with the basics: safety first, always. I can’t stress this enough. I’ve seen techs skip locking out the circuit “just for a second” and get zapped, so don’t do that. Grab your lockout-tagout (LOTO) kit, test the circuit with a multimeter to make 100% sure there’s no juice running through the switch before you touch it. Skipping this step is like walking into a construction site without a hard hat—invites disaster. Got that? Good. Now, let’s dive into the first check: visual inspection before even picking up tools. Most LBS issues are obvious if you just slow down. Walk the switch, check for loose bolts, cracked insulators (that’s the ceramic or plastic bits that keep current from jumping where it shouldn’t), or any debris—leaves, dirt, spider webs? Yep, spider webs, those tiny things can mess up insulation over time. I once had a customer call saying their LBS wouldn’t switch load, and it turned out a spider had built a web across the contacts—enough resistance to throw off the whole operation. So wipe down the insulators, tighten any loose hardware you see (but don’t over-tighten, those small bolts snap easy), and make sure the switch handle or actuator isn’t jammed. Sometimes kids or wildlife knock a tool or branch into the handle, so wiggle it gently to see if it moves freely.
Next up, functional testing when you’ve got power locked out. Wait, no—wait, when the circuit is de-energized, you want to test the mechanical operation first. Grab a feeler gauge if you have one, check the contact gap. LBS are designed with a specific gap between the moving and fixed contacts to prevent arcing when you open or close them. If that gap’s too big, the switch might not make solid contact when closing; too small, and it won’t break the load properly. If you don’t have a feeler gauge, just visually compare the gap to a new LBS part—if it looks way off, that’s your problem. Then, when you put power back (and only do this when you’re ready), test the load break. That’s the key part—if the switch just cuts the power without interrupting the load current, that’s a “load non-break” issue. You’ll see a big arc, maybe even smoke, which is a red flag. Why does that happen? Usually, worn contacts. The silver or copper-alloy contacts on LBS get pitted from use over time. If the pitting is deep, the surface isn’t smooth enough to break the current without arcing. If that’s the case, you can file the contacts lightly (don’t grind ’em down too much, you’ll remove too much material) or replace the contact insert. As a supplier, I’ve seen customers try to reuse pitted contacts and end up having to replace the whole switch, so save yourself the hassle and check that contact surface.
Another common issue: the switch won’t stay closed or won’t open at all. That’s usually a problem with the latch mechanism. LBS have a latch that keeps the contacts in place when closed, and a trigger that releases them to open. Over time, dirt, grease, or corrosion can gunk up that latch. To fix it, take apart the latch housing (make sure it’s de-energized!) and clean the parts with electrical contact cleaner, not regular WD-40—WD-40 leaves a sticky residue that attracts more dirt. Then, apply a tiny bit of silicone lubricant, not too much, because you don’t want it getting on the contacts. If the latch is broken, you’ll need to replace the latch assembly, which is way cheaper than a new switch. I always tell customers to keep spare latches on hand—they’re small, cheap, and a quick swap fixes 70% of latch issues.
Wait, what if you’re getting weird voltage readings? Like, when the switch is closed, you expect 12kV, but you’re only getting 10kV on the load side. That’s a voltage drop issue, which points to bad contacts or loose connections. First, check the terminal lugs—where the wires connect to the switch. Loose lugs cause high resistance, which leads to voltage drop and even overheating. Use a torque wrench to tighten the lugs to the manufacturer’s specs (don’t guess—check the manual, or if you lost it, hit me up and I can send it, no cost). If tightening doesn’t fix it, the contacts are probably worn, like I mentioned earlier. Sometimes, a bad ground connection can also cause voltage issues. Check the ground wire on the switch—make sure it’s not corroded, and the clamp is tight. I had a utility company tell me their LBS was underperforming, and it turned out the ground clamp was rusted so bad there was no connection at all. That’s an easy fix once you find it.
Now, let’s talk about arcing—because arcing is the main reason LBS fail. Small arcs are normal when you switch the load, but big, sustained arcs are a problem. Why? If the contact gap is wrong, or the contacts are pitted, the arc doesn’t extinguish right. Or maybe the arc chute (that’s the part that’s designed to cool the arc and put it out) is damaged. The arc chute is made of ceramic or fiberglass, and if it’s cracked, it can’t do its job. If you see a cracked arc chute, replace it immediately—don’t run the switch with a broken arc chute, it’ll destroy the whole switch, maybe even cause a fire. Another arcing culprit: moisture. If the LBS is outdoors and the seals are bad, water gets inside, which reduces insulation and causes arcing. Check the gaskets on the switch housing—if they’re cracked or flattened, replace them. I’ve had customers in rainy regions go two years without checking gaskets, then have a major arcing event when a storm hits. So seasonal checks, especially before wet seasons, are a good habit.
What about if the switch is electronically actuated, not manual? A lot of newer LBS have motorized or spring-actuated controls for remote operation. If that’s your setup, troubleshooting is a bit different. First, check the power to the actuator—make sure the batteries (if wireless) are charged, or the control power supply is working. If the actuator hums but won’t move, check the gearbox—sometimes dirt gets in there, or a gear is stripped. You can take the gearbox apart (again, de-energized!) and inspect the gears; if a gear is stripped, order a new one, or if you come to me, I can send a replacement gear assembly fast. Another electronic issue: the limit switches that tell the actuator when the switch is fully open or closed. If those limit switches are out of adjustment, the actuator will keep running, which can burn out the motor. To fix that, adjust the limit switch sensors so they trip exactly when the switch reaches the open or closed position. Easy, but you have to be precise—too loose, and the motor runs too long; too tight, and the switch doesn’t seat all the way.
Wait, let’s add a real quick tip I learned the hard way: don’t skip the load test. Once you’ve fixed whatever issue you found, do a test switch under load, not just de-energized. Put the circuit back online, flip the switch, and watch for the arc. If it’s a small, clean arc that goes away right away, you’re good. If it’s big and fuzzy, go back and check the contacts and gap. I once missed this step after replacing contacts, and the arc was so bad it melted a portion of the insulator. That cost a customer a whole day of downtime, and I felt terrible—so now I make sure to remind everyone to do the live load test, even if it’s a bit nerve-wracking.
Now, let’s cover when you should just replace the LBS instead of troubleshooting. If you see a cracked housing, internal corrosion (like rust inside, which you can’t see from the outside but will show up as weird current readings), or the contact inserts are worn down to the point where they’re too thin to replace, it’s time for a new switch. Trying to patch those issues will just lead to more problems later. As a supplier, I always tell customers to balance repair cost vs. replacement cost—if a new LBS is only 20% more than the cost of parts and labor to fix the old one, go new. It’ll be more reliable long-term, and you won’t have to deal with unexpected downtime.
Let me wrap this up with some quick do’s and don’ts to remember: Do lock out the circuit before working on the switch. Do clean contacts and latches regularly to prevent gunk buildup. Do keep spare parts (latches, contacts, gaskets) on hand. Don’t guess on torque specs—use a wrench, not your hand strength. Don’t run a switch with a broken arc chute or corroded ground. Most importantly, don’t rush troubleshooting—take your time, check each part step by step. LBS are tough, but they’re not indestructible, and a little care goes a long way.

If you’re still having issues after going through all these steps, or you need help sourcing replacement parts, hit me up to connect for a supply or procurement chat. No pressure, just real support for anyone working with loadbreak switches.
Transformers References:
- ANSI C37.100-2018, Standard for AC High-Voltage Switchgear and Control Equipment Rated Above 1000 V
- IEEE Std. 95-2012, Recommended Practice for Maintenance, Testing, and Replacement of Outdoor High-Voltage Switchgear
- Loadbreak Switch Manufacturer’s Field Service Guide, National Electrical Manufacturers Association (NEMA)
- Occupational Safety and Health Administration (OSHA) Lockout-Tagout Standard 29 CFR 1910.147
Wenzhou Shuowei Electric Co., Ltd.
Wenzhou Shuowei Electric Co., Ltd. is one of the most professional loadbreak switch manufacturers and suppliers in China, specialized in providing high quality customized service. We warmly welcome you to wholesale bulk loadbreak switch in stock here from our factory. Contact us for quotation.
Address: No.208 Wei 12 Rd, Yueqing Economic Development Zone, Wenzhou, China
E-mail: admin@suvell.com
WebSite: https://www.suvell.com/