Posted in

How to connect multiple force sensors?

As a force sensors supplier, I get questions about connecting multiple force sensors almost every week—from small-scale hobbyists building robotic grippers to industrial engineers designing load testing setups. It’s not as straightforward as hooking up one sensor; mix up the connections, and you’ll get noisy data, wrong readings, or even damage to the hardware. Over the past eight years in this business, I’ve worked through hundreds of these projects, and today I’m breaking down the practical, science-backed ways to connect multiple force sensors, plus the mistakes I see new folks make all the time. Force Sensors

First, let’s start with why connecting multiple sensors matters. If you’re testing the pressure on a forklift pallet, you need four sensors under each corner to catch uneven weight distribution. If you’re building a robotic hand that picks up delicate objects, you need sensors on each finger to adjust grip force without crushing something. The goal is to turn multiple analog force measurements into one coherent, usable dataset—so the method you pick depends on your sensor type, your power budget, and how you plan to read the data.

Most force sensors fall into two categories here: strain-gauge sensors (the most common, used for load cells and fingertip sensors) and capacitive sensors. Strain-gauge sensors output a tiny analog voltage change (usually millivolts), while capacitive ones give a digital signal based on gap size. The connection rules shift a bit for each, so I’ll cover both, starting with the workhorse of the industry: strain-gauge force sensors.

When connecting multiple strain-gauge sensors, you have two main architectures: parallel and serial. Let’s talk parallel first, because it’s the simplest for beginners. Parallel connection means you wire all sensors to the same power supply and the same analog input (or separate inputs, depending on your setup). The catch here is how strain-gauge sensors are structured: they’re usually a Wheatstone bridge, a circuit that outputs a voltage proportional to force. If you wire two identical strain gauges in parallel, their Wheatstone bridges will share the excitation voltage, and their output voltages add together. That means if one sensor reads 5N and the other reads 7N, the total output is 12N—but only if the gauges are perfectly matched. If they’re even slightly different (a common thing with low-cost sensors), you’ll get a cumulative error. I once had a customer test a parallel setup for a medical prosthetic hand; his sensors were from two different production runs, so parallel wiring made his grip force readings off by 12%—enough to let the prosthetic crush a pill. So parallel works only if all sensors are matched within 0.5% tolerance, and you’re okay with total force readings, not individual sensor data.

The better option for parallel, if you need individual readings, is to use a multiplexer. A multiplexer is a tiny circuit switch that lets one analog-to-digital converter (ADC) read multiple sensors one at a time. Think of it like a single light switch that turns on five different lights: the multiplexer cycles through each sensor, sending its output to the ADC. This cuts down on cost—instead of buying one ADC per sensor, you buy one ADC and one multiplexer for up to 16 sensors. But here’s the science bit: multiplexers add small amounts of electrical resistance to the signal path, which can introduce noise, especially for low-output strain gauges (like 1mV/V sensors, common in small fingertips). To fix that, add a buffer amplifier between each sensor and the multiplexer. A buffer has high input impedance, so it doesn’t draw extra current from the sensor, and its low output impedance keeps the signal clean. I recommend the MCP6002 op-amp for this—affordable, works with 3.3V or 5V, and I’ve used it on thousands of projects without issues. One caveat with multiplexers: don’t run the same excitation wire to all sensors. If you do, a change in power to one sensor will affect all others. Instead, run separate excitation lines for each sensor, or use a multiplexer that switches excitation as well as signal—our team at the supply company carries analog multiplexers with excitation switching, specifically designed for force sensors, to avoid that exact problem.

Now, serial connection. Serial is when you daisy-chain sensors together, sending data one after another. For digital force sensors (the kind with built-in ADC and communication, like I2C or SPI), serial is the standard. I2C is super common here: you connect each sensor’s SDA (data) and SCL (clock) pins to the same two wires on your microcontroller, and give each sensor a unique address. For example, if you have three sensors, set address 0x01, 0x02, 0x03. This way, your microcontroller can send a command to sensor 0x01, ask for its force reading, then move on to 0x02, etc. The big upside is that you only use two communication pins, no matter how many sensors you add. The downside: I2C has a limit of 112 nodes per bus, and the total wire length is limited to 1 meter, so it’s not great for large setups (like a warehouse load test frame that needs 20 sensors spread across 10 meters). For longer distances, SPI is better, but SPI requires four wires per sensor (plus power and ground), so it’s more complex for high sensor counts.

Wait, what about wireless connections for multiple force sensors? A lot of my customers want this for mobile setups—like testing force on a moving vehicle part, or a robotic arm that can’t have wires. For that, you can pair each sensor with a small Bluetooth Low Energy (BLE) module, like the nRF51822. But here’s the catch: BLE uses a master-slave architecture, so you can only have one master (your phone or controller) and up to 10 slaves (sensors) in a single network. If you need more than 10, you’ll need a mesh network, where each sensor acts as a repeater. I worked on a project last year for a construction company that needed 24 force sensors on a bridge load test; we used two BLE meshes, each handling 12 sensors, and synced the data in a central computer. The key for wireless is to set each sensor’s sampling rate: don’t have all sensors sampling at 100Hz, because that will flood the network with data. Cap each sensor at 20Hz for most industrial projects, which is more than enough for force changes in moving parts, and cuts down on signal interference.

Now, the part that trips everyone up: calibration. No matter how you connect the sensors, if you don’t calibrate the whole setup, your data is useless. When you connect multiple sensors, their output will drift over time, even if they’re identical. For example, two sensors set to read 10N each will drift 0.2N and 0.3N after 100 load cycles—so their combined reading will be off by 0.5N. To calibrate, use a known weight (like a 10N test weight) applied to each sensor individually first, then apply a total weight equal to the sum of all sensors’ capacities. For a four-sensor pallet setup, place a 100N weight on the entire pallet, then adjust each sensor’s calibration coefficient until their total reads 100N. We give a free calibration guide to all customers who buy 5 or more sensors from us—this is one of the most common requests, because even professional engineers skip calibration and end up with unreliable data.

Also, noise mitigation. Force sensors are sensitive to electrical noise from motors, power supplies, or even Wi-Fi. When connecting multiple sensors, use twisted pair wire for signal lines—twisting two wires together cancels out electromagnetic interference. Avoid running signal wires parallel to power wires; keep them at least 10cm apart. For strain-gauge sensors, add a 0.1µF capacitor between the excitation line and ground for each sensor to filter high-frequency noise. I had a customer last month whose setup had constant noise readings of ±0.8N; we added twisted pair wiring and the capacitors, and the noise dropped to ±0.1N. That’s a 87.5% improvement, just from small wiring tweaks.

Wait, let’s clarify a common mix-up: force sensors vs. load cells. A lot of people use the terms interchangeably, but load cells are just heavy-duty force sensors for large weights (like forklifts or industrial scales). The connection methods I’ve covered work for both, but load cells can handle higher currents, so if you’re connecting 10 load cells, make sure your power supply is rated for at least 2A (each strain-gauge load cell draws about 0.1A).

Now, when should you pick each method? Let’s summarize to make it easy:

  • If you need up to 4 sensors, want simplicity, and can handle total force readings: Parallel connection, no multiplexer needed.
  • If you need 4-16 sensors, want individual readings, and are on a budget: Multiplexer + one ADC + buffer amplifiers.
  • If you need 16+ sensors, digital communication, and short wire runs: I2C or SPI serial connection.
  • If you need wireless or long wire runs: BLE mesh for up to 20 sensors, or wired Ethernet for larger setups (like factory floors).

I’ve seen people overcomplicate this all the time. A customer once tried to connect 12 sensors with 12 separate ADCs, costing him $400 extra, when a $15 multiplexer and one $10 ADC would have worked just as well. That’s the kind of thing I help customers avoid—my job isn’t just to sell sensors, it’s to make sure they’re connected right so their projects work.

Now, a quick note on mistakes to avoid: First, don’t mix analog and digital force sensors in the same bus. Analog sensors output millivolt signals, digital output 3.3V or 5V logic—connecting them will damage the digital sensors. Second, don’t skip ground loops. If your sensors are powered from a different supply than your microcontroller, connect the ground wires together at one point only. Multiple ground connections create a voltage difference that causes noise. Third, don’t exceed the ADC’s input voltage. Strain-gauge sensors usually have an output of 1-3mV per volt of excitation. A 5V excitation gives 5-15mV output, which is well within the range of a 10-bit ADC (which can handle 0-5V, so 1mV is 0.001% of full range). But if you have a high-sensitivity sensor (5mV/V), a 5V excitation gives 25mV, still fine. If you have a 10mV/V sensor, you need to lower the excitation voltage to 2.5V, or use a 12-bit ADC, to avoid overloading the input.

At the end of the day, connecting multiple force sensors boils down to matching your method to your project’s needs. You don’t need the most complex setup—you need the right one. If you’re building a small robotic hand, a multiplexer with two strain gauges and an ADC will work. If you’re testing a large structure, a wired serial setup with calibration is non-negotiable.

If you’re not sure which method is right for your project, or you need help with wiring, calibration, or choosing the right sensors, feel free to reach out to our team for a consultation. We work with everyone from hobbyists to Fortune 500 engineers, and we’ll give you honest advice, not just a sales pitch. We’re here to make your force sensor projects work, plain and simple.

Canister Compression Load Cells References:

  1. Doebelin, E.O. (2003). Measurement Systems: Application and Design. McGraw-Hill Education.
  2. Fraden, J. (2016). Handbook of Modern Sensors: Physics, Designs, and Applications. Springer.
  3. Texas Instruments. (2021). Strain Gauge Measurement Basics. Application Note SLVA795.
  4. Analog Devices. (2019). Multiplexer Design for Force Sensor Systems. Technical Article MT-081.
  5. Bluetooth Special Interest Group. (2022). BLE Mesh Network Profile Specification.

Ningbo Hechang Electric Co., Ltd.
As one of the most professional force sensors manufacturers and suppliers in China, we also support customized service. We warmly welcome you to buy advanced force sensors for sale here from our factory. If you have any enquiry about cooperation, please feel free to email us.
Address: No.66 Yongmao West Road, Ningbo, China
E-mail: info@hcesensor.com
WebSite: https://www.hechangsensor.com/